Serpent SER600039-O Serpent Cobra E-Truggy RTR Orange  [SER600039-O]

Serpent SER600039-O Serpent Cobra E-Truggy RTR Orange
價格:
HKD$2,828.87
牌子:
Serpent
型號:
SER600039-O
請輸入姓名和電子郵件地址。當貨品重新上架我們將笫一時間通知閣下.
你或可於 R/C Models - Off-Road - Truggy - Electric Powered
類別中嘗試尋找類似的產品
填寫評論
  • Introduction

    The Serpent Cobra E-Truggy in RTR trim is a perfect basher type vehicle that will take lots of beating and its also a fantastic package to start real racing ! In line with the Cobra E-Truggy this has the outright speed, great management, reliability, rigidness and durability you need.

    The RTR package is really dialed:
    -factory assembled rushing chassis
    -prepainted and precut low kind truggy body and big composite backside wing
    -premounted truggy tyres/wheels/inserts
    -pre-set 4S to 6S capable waterproof 150A speedo ( DragonRC)
    -2000kv brushless longbody motor (DragonRC)
    -Digital 2.4ghz transmitter (DragonRC)
    -Metal gear servo 16kg ( DragonRC-Savox)
    -3 oilfilled geardifferentials
    -Big bore shocks with rubber dustboots and machined aluminium shocktowers
    -Spring steel transmission parts and turnbuckles, front side and back cvd driveshafts
    -Front and back anti-roll bars
    -Large battery-cases with simple felcron straps
    -Machined aluminium chassisplate
    -Fully ballraced
    -Batteries for the vehicle and transmitter are not included

    The bodyshell comes in orange, red, green, blue and red, along with a clear type.

    Serpent provides a multitude of optional parts with this automobile to further improve performance, lighter or even for also nicer looks.

  • Main features

    Car
    Fully expert pre assembled and pre-set chassis and electronics.

    Transmitter
    DragonRc 2.4 GHz steeringwheel kind transmitter with plenty settings and good range. Is sold with little and light receiver.

    Speedo
    DragonRC waterproof speedcontroller with an enormous 150A capability to control the brushless motor and 4S or 6S battery pack power

    Motor
    DragonRC longbody 2000kV brushless motor with easy colorcoded connectors

    Body
    Prepainted and pre-cut low e-Truggy human body, in 4 primary colors orange, red, Green and Blue. ( also clear one available as optional)

    Tyres
    Premounted battle prepared tyres / wheels with soft substances and pintype profile for amazing grip.

    Chassis
    Very narrow 3mm 7075T6 aluminium chassis, with machining on the top face making it lighter in strategic areas also to get a handle on flex. Kick-up front for appropriate landings. Angled part to boost cornering approval, and protected and easy mounting side guards with 5 screws. Countersunk holes, pouches to position the suspension system brackets. In general the Truggy is designed to keep consitently the fat very main and towards the centerline as you can, to produce outstanding overall stability.

    Side guards / battery pack trays
    Durable shaped composite part guards / battery pack trays that proceed with the line of the framework, and mount with 5 screws each side. Front and edges high enough to help keep the dirt away. The guards/trays create some stability. The batteries are mounted in longtudinal fashion, keeping the weight low in car. The battery pack trays features simple to use Serpent marked felcron TM straps to secure the batteries in position. Fits 2S and 3S batteries.

    Motormount:
    The engine is positioned into the most optimal position in the car, keeping motor-forces and transmission components / positioning in mind. Only one-screw is needed to secure the BL engine, within the nicely created durable machined aluminium motormount. Space for extra motor-cooling available as required. The room the motor permits mounting all popular buggy and (monster)truggy motors.

    Composite framework braces
    Allows the chassis to flex which assists improve bump managing. Front and rear.

    Front bumper
    Nicely rounded front bumper, same as in the Cobra buggy, to protect the front anti-roll bar, suspension system brackets, and moves inline with kick-up framework front side for safe landings.

    front side suspension
    Very long and durable composite reduced wishbones, combined with upper spring-steel trackrods. 2 reduced shock-mount positions. Downstops can be used as required. Pivotball type anti-roll bar rods.
    .
    Front steering / servo saver / angled
    Innovative angled front side steering assembly to cut back the angle of distinction between the sum total caster and steering airplane. Therefore you'll have less bump steer and a truer steering Ackerman through the complete array of suspension.

    Adjustable spring packed servo-saver system with interchangeable Ackermann dishes. Using the design regarding the steering bell cranks whenever changing the Ackerman you'll not must adjust your steering tie rods. You just will only should adjust your end points on your own radio.. Very easy to gain access to and set-up.

    The Inboard Bell crank keeps the lever and linkage within the automobile. It'll help with the prevention of damage to the steering system. Zero scrub radiuses on steering knuckle, assists in easing the jacking effect produced by your steering knuckle offset. It provides a more direct fell while keeping the cars chassis more degree while turning.

    The front roll center are changed quickly by moving the steering knuckle shims with their appropriate locations.

    Topped of with a good composite top-plate.

    Front steering-block / c-hubs
    Very durable front side steeringblock / C-hub installation .

    Drive-shafts
    Long and lightweight spring metal units with pressed in steel pins, laser-engraved. Exact same length front side and rear.

    Wheel-axles / wheel-nut
    Serpent springtime steel threaded wheel-axles with lightweight grey anodised aluminium wheel-nuts to help keep the huge truggy wheels/tyres on track.

    Captured universal joints
    Guarantees you will definitely complete a race without loosing a pin or set screw. All parts, axles and drive train components have actually capture pins

    Front shocktower
    Light, strong and durable machined 5mm aluminium units with 5 roles for shockangle.

    Shock-set front side and rear
    16mm big bore shocks, with difficult anodized accuracy threaded shock-bodies. Shockboots in silicone rubber to help keep the dirt out . Chromed shock-shafts for supersmooth shockaction . The larger o rings offer less general force and a much better seal without dragging regarding the surprise shaft.

    Suspension brackets
    The hinge-pins / hingepin balls are captured in durable composite suspension system brackets . These capture the nylon roll-center inserts.

    Anti-roll club / anti-roll club linkage with pivotball
    The anti-roll pubs front and rear are made of high quality special springtime metal, and are also captured in the diff-cased in ballbearing for perfect guidance and control.

    Receiver field / servo mount / speedo mount
    Composite one piece radiobox to firmly install servo� s, speedo and receiver. For maximum balance the light receiver fits the top-case simple, with a tiny opening to permit cable to protrude. The speedo seats really low on a plate just over the chassis, therefore quick cables may be used to the engine. The servo is installed in a vertical fashion.

    Central diff
    Optimised central gear-diff with 50T super-hard spur-gear . Really small, compact design to reduce rotating mass towards the max.

    Transmission shafts
    Durable but light and thin Serpent spring steel, laser engraved shafts.

    Front and back diff
    Optimised gear-diff with superhard spur-gears . Very small, compact design to cut back rotating mass on max. Same variation front and rear. Diff coupler in spring steel seated in large barings for durability.

    Rear shocktower
    Light, strong and durable machined 5mm aluminum product with 5 roles for shockangle.

    Rear uprights
    Durable composite back uprights with 3 camber positions

    Suspension brackets rear
    Durable composite devices with eccentric inserts to change set-up.

    Rear wing mount
    The composite back wing mount, permits to improve the angle of this rear wing.

    Rear wing
    Two phase high down force wing, has two levels of angle, which also includes 2 fins. Helps improve down force and straight line capability

    Bodymounts
    Nylon bodymounts with wider sitting the human body, firmly fastened towards shocktowers.

    Super Minimal profile e-Truck Body
    Improves appearance including keeps the profile minimum. Comes precut and prepainted.

    Decals
    Applied to the human anatomy.

    Oils / grease
    Car is put together with high quality silicone oils the diffs and shocks and black oil. Threadlock used in which needed.

    Manual
    Full color manual showing the car, specifications, tips and exploded views. The transmitter and speedo have small split manuals included.

    Box
    Full color protective box to re-use for vehicle transportation or tyres.





Copyright © 2013-2024 rcjaz.com.hk 版權所有